Top5: Arduino programming interface | Test & Advice

Exploring Arduino: Tools and Techniques for Engineering Wizardry

19.20 $ 35.00 $ -45%

Arduino: The Essential Step by Step Guide to Begin Your Own Projects (DIY Programming Projects, STEM)

0.99 $
Raspberry Pi Cookbook: Software and Hardware Problems and Solutions

30.59 $ 49.99 $ -39%

30 Arduino Projects for the Evil Genius, Second Edition

23.36 $ 25.00 $ -7%
NodeMCU ESP8266 Communication Methods and Protocols : Programming with Arduino IDE

2.99 $
Robot Programming: A Guide to Controlling Autonomous Robots

11.99 $
Arduino + Android Projects for the Evil Genius: Control Arduino with Your Smartphone or Tablet

20.31 $ 25.00 $ -19%
SparkFun Artemis Development Kit - Updated USB Interface Drag and Drop Programming SWD Interface JTAG Programming PTH Debug Mass Storage Device Human Interface Device 5V Power

An updated USB interface (MKL26Z128VFM4 Arm Cortex-M0+ MCU, from NXP). Compatible with Arduino, Mbed OS, and AmbiqSDK Development Programs. Drag and Drop Programming, SWD Interface, and JTAG Programming PTH Mass Storage Device (MSD): Used to provide drag and drop programming to the Artemis Module. Human Interface Device (HID): Used for the debugging interface to the Artemis Module. Communication Port (COM): Used to provide a serial communication UART between the Artemis and the USB connection (PC). Power:5V Provided Through the USB-C Connector and 1.8V, 3.3V, and 5V Available on Power Header. Qwiic Connector On Primary I2C Bus Artemis Module:Apollo3 ARM Cortex-M4F MCU, BLE 5.0 with FCC/IC/CE Certification 8/16/2019 (ID Number 2ASW8-ART3MIS), 24 Breakout I/O Pins, Eight 14-bit ADC Pins, Eighteen 16-bit PWM Pins, Two Independent UART Ports, Three Peripheral I2C/SPI Buses, JTAG Programming PTH Sensors: 3-axis Accelerometer (LIS2DH12), PDM Microphone (SPH0641LM4H-1), Camera Connector (for the Himax HM01B0 Camera). Board Only

44.95 $
SparkFun Artemis Development Kit with Camera - Updated USB Interface Drag and Drop Programming SWD Interface JTAG Programming PTH Debug 5V Power Himax HM01B0 Camera Reversible USB A to C - 0.8m

An updated USB interface (MKL26Z128VFM4 Arm Cortex-M0+ MCU, from NXP). Compatible with Arduino, Mbed OS, and AmbiqSDK Development Programs. Drag and Drop Programming, SWD Interface, and JTAG Programming PTH. Includes: 1x Artemis Development Kit (Board), 1x Himax HM01B0 Camera, 1x Reversible USB A to C - 0.8m Mass Storage Device (MSD): Used to provide drag and drop programming to the Artemis Module. Human Interface Device (HID): Used for the debugging interface to the Artemis Module. Communication Port (COM): Used to provide a serial communication UART between the Artemis and the USB connection (PC). Power:5V Provided Through the USB-C Connector and 1.8V, 3.3V, and 5V Available on Power Header. Qwiic Connector On Primary I2C Bus Artemis Module:Apollo3 ARM Cortex-M4F MCU, BLE 5.0 with FCC Certification, 24 Breakout I/O Pins, Eight 14-bit ADC Pins, Eighteen 16-bit PWM Pins, Two Independent UART Ports, Three Peripheral I2C/SPI Buses, JTAG Programming PTH Sensors: 3-axis Accelerometer (LIS2DH12), PDM Microphone (SPH0641LM4H-1), Camera Connector (for the Himax HM01B0 Camera)

50.95 $
AITRIP 6pcs ESP8266 ESP-01 ESP-01S RGB LED IDE WS2812 Controller Adapter Module for Arduino for Arduino IDE Programming

WS2812 RGB LED control module based on ESP-01 / 01S. With it, you can easily control the WS2812 light bar / light ring. DIY own lighting control system. Support for Ard uino IDE programming. Control Pin: GPIO2 Operating Voltage: DC 3.7V-5V (Please note: The positive supply voltage VCC on the board is connected to the VCC on the WS2812 3PIN connector. Therefore, if your light bar / lamp ring is 5V powered, use DC 3.7V-5V power supply.) Interface: 3Pin PH2.0 connector； Support 3.7V lithium battery Application example:Download the program to ESP-01S；Power supply: 3.7V-5V DC power supply to the VCC GND (2.54mm pin)； Insert the ESP-01 / ESP-01S into the 2 * 4 Pin header

11.99 $