Top10: Arduino programming attiny85 | Test & Recommendation

The Digispark is an Attiny85 based microcontroller development board similar to the line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much. The Digispark is shipped fully assembled except for the two included and easy to solder headers. Support for the Arduino IDE 1.0+ (OSX/Win/Linux) Power via USB or External Source - 5v or 7-35v (12v or less recommended, automatic selection) 6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB)

Support for the . IDE 1.0+ (OSX/Win/Linux). Power via USB or External Source - 5v or 7-35v (automatic selection). On-board 500ma 5V Regulator. Built-in USB (and serial debugging). 6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB).

74HC Series High-speed Si-gate CMOS Logic ICs Assorted Kit. 30 Types, total 30 PCS (each 1 PCS), all DIP package. Packed in a plastic box. 100% New, Never Used. RoHS Compliant.

The item has been soldered and assembled. Support for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B GPIO status LED and power 5V / 3.3V indication. GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO. Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. 2 x 20 pins expansion pin header, height 8mm/0.32". Packing list: 1x terminal block breakout module, 4x M2.5x16mm nylon standoffs, 4x M2.5x6mm nylon standoffs, 4x M2.5 nylon nuts(NOTE: the item not include Raspberry Pi Board).

This product can easily mount Raspberry Pi / Arduino / BeagleBone to DIN rail, expand their range of applications to industrial control. Supports Raspberry Pi 1 Model A+ / Pi 1 Model B+ / Pi 2 Model B / Pi 3 Model B / Pi 3 Model B+ / Pi 4 Module B / Pi Zero / Pi Zero W, Arduino Uno R2 / Uno R3 / Mega 2560 R2 / Mega 2560 R3 / MKR Series etc, and BeagleBone / BeagleBone Black / BeagleBone AI / BeagleBone Black Wireless / BeagleBone Green / BeagleBone Green Wireless or SanCloud BeagleBone Enhanced. High quality DIN rail feed and mounting very stable, can support width 35mm / 32mm / 15mm DIN rail. Support horizontal and side installation. The position of the DIN rail feet can be adjusted according to the situation. And the carrier feet can be taken apart for wall-mount use. Thickness 1.5mm/0.06" aluminum bracket sheet, the weight is very light and very strong. Package included: 1x Aluminum bracket, 1 pair DIN rail adapter feed and mount screws, 6x M2.5x10mm standoffs, 12x M2.5x6 pan head screws, 4x M2x12mm standoffs and 8x M2x6mm screws(for Arduino MKR). NOTE: the item not include Arduino Mega and iron DIN rail.

3.5" TFT LCD Display ILI9486/ILI9488 480x320 Suitable for MEGA2560 Support Arduino Mega2560 Directly inserted OnBorad level conversion chip for 5V/3.3V MCU Compatible with 3.3/5V operation voltage level Compatible with Arduino-Series development Board. (Please notice:This Screen is not touch screen)