- Degraw 40 kg Tension Load Cell and HX711 Combo Pack Kit - Load Cell Amplifier ADC Weight Sensor for Arduino Scale - Everything Needed for Accurate Force MeasurementU.S. BASED SUPPORT - contact Degraw through Amazon messages for help with setting up the kit LOAD CELL - Sturdy steel alloy construction. Removable hooks pre-attached. Strain gauges pre-attached with strain relieved wires. Accurately measures forces from 0-40kg (0-88 lb). HX711 - This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller (like an Arduino or Raspberry Pi). LOAD CELL SPECS - Removable hooks pre-attached, 16 cm (6.25 in) hook-to-hook. Wire leads pre-attached, 12 cm (4.5 in) long. Load cell dims: 2.8 mm thick, 7.6 mm wide, 40 mm long (.11 in x 0.3 in x 1.56 in). 2 mounting holes, 4.2 mm diameter, 6 mm (.25 in) distance from tip. HX711 SPECS - Operation Voltage: 2.7V–5V | Operation Current: < 1.5mA | Includes breakaway headers for connection, soldering required
- AiTrip 6pcs Hx711 Weight Weighing Load Cell Conversion Module Sensors Ad Module for Arduino MicrocontrollerTwo selectable differential input channels On-chip active low noise PGA with selectable gain of 32, 64 and 128 Simple digital control and serial interface: pin-driven controls, no programming needed Selectable 10SPS or 80SPS output data rate Size:25mmx16mm/0.98"x0.62"(inch) (approx)
- DAOKI 4pcs DIY 110lbs 50KG Half-Bridge Body Load Cell Weight Strain Sensor Resistance + HX711 AD ModuleSize:15mm*11mm Power:2.5-5.5V Trigger setting mode:(1- Greater than Short;0- Greater than No Short COLOR:RED Material: CCL
- DFRobot Gravity: Analog Infrared CO2 Sensor For Arduino (0~5000 ppm)DFRobot released its latest high-precision analog infrared CO2 sensor. The effectively measuring range is from 0 to 5000ppm This sensor is based on non-dispersive infrared (NDIR) technology and has good selectivity and oxygen-free dependency Besides, its service life could up to 5 years! It integrates temperature compensation and support DAC output Most importantly, the product is easy to use; it is compatible with all types of microcontrollers such as Arduino with ADC function63.00 $
- 5PCS HX711 Load Cell Amplifier Breakout Weight Weighing Sensors Ad Module Analog to Digital Converter, for Arduino Raspberry Pi MicrocontrollerOperation supply voltage range: 2.6 ~ 5.5V What you will get: 5pcs HX711 Load Cell Amplifier How to email us? Please click “Stemedu”(you can find "Sold by Stemedu" under Buy Now button), in the new page, click “Ask a question” to email us7.99 $
- SparkFun Load Cell Amplifier - HX711 Small Breakout Board Read Load Cells to Measure Weight Four-Wire Wheatstone Bridge Configuration Connect to sensors Build Scale Process Control Presence DetectionWeigh items very accurately. Some calibration required. Separated analog and digital supply Two-wire interface (Clock and Data) for communication with a microcontroller GPIO pins Operation Voltage: 2.7V--5V. Operation Current: < 1.5mA. Selectable 10SPS or 80SPS output data rate. Simultaneous 50 and 60Hz supply rejection9.95 $
- Electronics-Salon Screw Terminal Block Breakout Module, for Arduino MEGA-2560 R3.Terminal Block Breakout Module - for Arduino MEGA-2560 R3. the item has been soldered and assembled. Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper. With power on LED indicating. red reset button on the side. with a ICSP adapter connect header. FR-4 fiber glass PCB, dual copper layers. NOTE: the item not include Arduino Mega module32.00 $
- Adafruit 4494 Adafruit DPS310 Precision Barometric Pressure/Altitude Sensor - Stemma QT/Qwiicperfect for measuring altitude changes with a up to ±0.002 hPa (or ±0.02 m) precision high precision mode and ± 1 hPa absolute accuracy. a great sensor for use in drones or other altitude-sensitive robots use it with 3.3V (Feather/Raspberry Pi) or 5V (Arduino/ Metro328) logic levels since it speaks I2C you can easily connect it up with two wires (plus power and ground!).12.99 $
- HiLetgo GY-906 MLX90614ESF Non-contact Infrared Temperature Sensor Module IIC I2C Serial for ArduinoMLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer. The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C. The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.14.99 $
- Degraw - 4 pcs 50kg Load Cells and HX711 Combo Pack Kit | Load Cell Amplifier ADC Weight Sensor for Load Cell Arduino | Bathroom Scale kitU.S. BASED SUPPORT - contact Degraw through Amazon messages for help with setting up the kit LOAD CELLS - 4 pcs - Sturdy steel construction with strain gauges pre-attached with strain relieved wires. Accurate measures forces from 0-50kg (0-100 lb). HX711 - This top of the line load cell amplifier mounted on a breakout board pairs perfectly with the load cell to provide fast, accurate force measurements. It measures small changes in the resistance of the strain gauges mounted to the load cell and passes these values directly to any micro controller (like an Arduino or Raspberry Pi). LOAD CELL SPECS - 34 mm x 34 mm x 7.8 mm, lead wires 300 mm long HX711 SPECS - Operation Voltage: 2.7V–5V | Operation Current: < 1.5mA | Includes breakaway headers for connection, soldering required12.99 $