Coach explains: Arduino programming language free download | Discount code

Designed for short range BT interactions and power savvy projects. Small (48mm x 18mm) and robust board is built around the NINA B306 module, based on Nordic nRF 52840 and containing a powerful Cortex M4F. The board’s architecture is fully compatible with Arduino IDE Online and Offline with dedicated libraries; it has a 9 axis Inertial Measurement Unit (IMU) and a reduced power consumption compared to other same size boards. Clock 64MHz, Flask 1MB, RAM 256KB. Two 15 pin connectors - one on each side of the board. The board has an inbuilt IMU sensor. For more information about getting started with the board, please visit https://www.arduino.cc/en/Guide/NANO33BLE

Open-source software supports multi-languages: English, French, German, Portuguese, and Spanish! Supported protocols: JTAG, SPI, I2C Fast 16MHz RISC processor with 32KB internal memory Dual voltage (3.3v or 5v) and changeable via a side switch USB 1.1 / 2.0 / 3.0 / 3.1 compatible

Supports all AVR devices with ISP or PDI interface, and certain 51 Devices Programs both Flash and EEPROM,Supports Fuses and Lock Bit Programming Based on AT AVRISP mkII firmware,Upgradable to Support Future Devices Adjustable ISP programming speed up to 8M frequency,USB 2.0 compliant (full speed, 12Mbps) 3 optional cables to target board,Powered from USB bus, does not require external power supply

ATmega328 running at 16MHz with external resonator USB connection off board Supports auto-reset Max 150mA output Over current protected

The ease of use of a Nano board with the addition of secure IoT and BT connectivity Small (48mm x 18mm), robust and powerful board; 3.3V variant of the Nano family. Arm Cortex-M0+ microcontroller and a pre-certified ESP32-based WiFi and Bluetooth module from u-blox Clock up to 48MHz, Flash 256KB, SRAM 32KB, Secure WiFi and Bluetooth connectivity with a 6-axis IMU, ECC608A crypto chip provides IoT security. Two 15 pins connectors (one on each side) that are pin to pin compatible with the original Arduino Nano Pre-certified module with external processor ensures maintaining RF compliance when writing application code.Run directly from high voltages from lead or multi-cell Lithium-ion batteries providing 3.3V power supply to peripherals at significant output current On-board DC-DC power supply enables the board to be powered up to 21V maintaining high efficiency and offering a lot of current to external devices without overheating

★【Feature】: Support simultaneously burn with 4 Programmers each computer. The minimum volume and the lowest power consumption and do not feel any heat in process. All chips do not need external power supply, the low power consumption of its own to ensure that the USB port can provide enough power. ★ 【Scope of Application】: Best internal 40 pin over voltage protection, the strongest VCC/VPP 4-level overcurrent protection. The short-circuit do not reset the PC. Wide range of chip 15000+ support, support for serial and parallel series 40/44/48PIN large capacity FLASH. ★【Unique serial ICSP interface】: Supporting the serial download and high-speed parallel high voltage programming. Note: TL866CS does not support ICSP ★ 【Test CMOS4000 74/54 series】: Test CMOS4000 74/54 series integrated circuit. Can be located in the gate circuit error. Chip auto serial number is the most complete and practical. ★ 【RC Calibration】: Original chip encryptionoperation on AVR microcontroller with internal RC Calibration byte. The Decrypt software can not be directly run on another same type of chip.

Free PDF tutorial (30 lessons) Contains basic courses, sensor courses, comprehensive experimental courses from easy to difficult Support Arduino IDE, Mixly, mblock Scratch graphical programming. High quality kit with Development Board. 100% compatible with Arduino UNO R3 This is the most basic Arduino kit for the beginner, has all the component you need to start Arduino Tutorial Link：github.com/keywish/keywish-uno-starter-kit